2024 new designed ultrasonic water level sensor with measuer
distance 100mm-5000mm
Features
1. Compatible with the many kinds of this similar product.
2. High sensitivity
3. Readings can occur up to every 33mS(30Hz) within 3meters or
occur up to every 80ms(12.5Hz) within 10meters.
4. Free run operation can continually measure and output ranger
information
5. 9V-28V supply with very low average current draw
6. Multi-kind output type such as analog (40-20mA, 0/1-5V,
0/1-10V), RS485, Can bus.
7. Sensor operates at 40 KHz, 112 KHz, 175 KHz, 300 KHz, 1 MHz
Brief introduction of 2018 new designed ultrasonic sensor
This sensor provides very short to long-range detection and
ranging, in a compact, robust PVC or stainless steel housing,
designed to meet IP67 water intrusion. The power 9.0V-28V operation
detects objects from 0.1meters to 10meters and provides sonar range
information from 0.25meters out to 10meters out with 0.001meters or
0.01meters resolution. The interface output formats included are
pulse width output, analog voltage output 0/4-20mA current output,
NPN/PNP output and RS485,RS232 output modbus-RTU and modbus-ASCII
supported.
Parameters
|
General Specifications |
Sensing distance 100.4000mm |
Adjustment range 100.4000mm |
Unusable area 0.200mm |
Standard target plate 100mm×100mm |
Transducer frequency About 112kHz |
Response delay About 195ms |
Indicators/Operating means |
LED blue Power on |
LED yellow Indication of the switching state Flashing: program function object detected |
LED red permanently red: Error Red,
Flashing: program function,object not detected |
Electrical specifications |
Operating voltage UB 10.30VDC,ripple10%ss |
Power consumption P0 ≤900 mW |
Output |
Output type analogue output 0.10V |
Resolution evaluation range [mm]/4000, but ≥ 0.35 mm |
Deviation of the characteristic curve ≤0.2% of full-scale value |
Repeat accuracy ≤0.1% of full-scale value |
Load impedance 0.500 Ohm |
Temperature influence ≤2% from full-scale value |
Ambient conditions |
Ambient temperature -25.70°C |
Storage temperature -40.85°C |
Mechanical specifications |
Protection grade IP67 |
Connection Connector M12x1,4-PIN |
Material Housing Brass, nickel-plated |
Transducer Epoxy resin/hollow glass sphere mixture; Polyurethane foam |
Weight 60g |
External synchronization
The sensor can be synchronized by the external application of a
square wave voltage. A synchronization pulse at the synchronization
input starts a measuring cycle. The pulse must have a duration
greater than 100 μs. The measuring cycle starts with the falling
edge of a synchronization pulse. A low level > 1 s or an open
synchronization input will result in the normal operation of the
sensor. A high level at the synchronization input disables the
sensor. Two operating modes are available:
1. Multiple sensors can be controlled by the same synchronization
signal. The sensors are synchronized.
2. The synchronization pulses are sent cyclically to individual
sensors. The sensors operate in multiplex mode.
Internal synchronization
The synchronization connections of up to 5 sensors capable of
internal synchronization are connected to one another. When power
is applied, these sensors will operate in multiplex mode.
The response delay increases according to the number of sensors to
be synchronized. Synchronization cannot be performed during
TEACH-IN and vice versa. The sensors must be operated in an
unsynchronized manner to teach the evaluation limits.
Note:
If the option for synchronization is not used, the synchronization
input has to be connected to ground (0V) or the sensor has to be
operated via a V1 cable connector (4-pin).
Adjusting the evaluation limits
The ultrasonic sensor features an analogue output with two
teachable evaluation limits. These are set by applying the supply
voltage - UB or + UBto the TEACH-IN input. The supply voltage must be applied to the
TEACH-IN input for at least 1 s. LEDs indicate whether the sensor
has recognized the target during the TEACH-IN procedure. The lower
evaluation limit A1 is taught with - UB, A2 with + UB.
Two different output functions can be set:
1. Analogue value increases with rising distance to object (rising
ramp)
2. Analogue value falls with rising distance to object (falling
ramp)
Evaluation limits may only be specified within the first 5 minutes
after
Power on. To modify the evaluation limits later,
the user may specify the desired values only after a new Power On.
TEACH-IN rising ramp (A2 > A1)
- Position object at lower evaluation limit
- TEACH-IN lower limit A1 with - UB
- Position object at upper evaluation limit
- TEACH-IN upper limit A2 with + UB
TEACH-IN falling ramp (A1 > A2):
- Position object at lower evaluation limit
- TEACH-IN lower limit A2 with + UB
- Position object at upper evaluation limit
- TEACH-IN upper limit A1 with - UB
Default setting
A1: unusable area
A2: nominal sensing range
Mode of operation: rising ramp
Company Information
Xi'an Kacise is certified by ISO 9001-2008, GJB 9001B-2009, CE, intrinsic safety
explosion-proof and isolated safety explosion-proof, etc. which
assure our products are conform to the international standards.
We have been specializing in manufacturing pressure, level and flow
measuring instruments and related products for 10 years. We have
experienced technical and management personnel, through the efforts
of our entire staff, we have become a professional measuring
instrument manufacturer and solution provider. And we are
continuously trying to improve product quality.
Currently, Kacise sensor is already exported to America, Spain,
Australia, Chile and 20 other countries and regions, and received
many favorable feedbacks. Our overseas distributers are also
increasing. We regards “reasonable prices, efficient production
time and good after-sales service” as our tenet, and hope to
cooperate with more customers for mutual development.
Our Services
- Your inquiry will be replied in 24hours.
- Well-trained and experienced staffs to answer all your enquires in
fluent English.
- OEM&ODM, we can help you to design and your request will be put
into product.
- Distributorship are offered for your unique design and some our
current models.
- Protection of your sales area, ideas of design and all your private
information.
- Discounts are offered based on order quantities.
- We provide paid repair services for meter damages not arising from
manufacturing quality issues or meter damages not within the scope
of warranty.
FAQ
1. Q: What information need to be provided to choose the suitable model?
A: Please provide us: application field, range , output signal, medium( liquid type),
and power supply, so we can choose model and quote for you quickly.
2. Q: Are you a trade company or a manufacturer?
A: We are an ISO approved manufacturer specialized in level and
flow measuring instruments.
OEM & ODM service are available. Welcome to visit us.
3. Q: What is your MOQ?
A: To start our cooperation, sample order is acceptable.
4. Q: What is your delivery date?
A: The delivery date is about 3-15 working days after receipt of
payment.
5. Q: What is your payment terms?
A: We support T/T, PayPal and Trade Assurance.
For mass production order, it is 30% deposit in advance and 70%
balance before shipment.
6. Q: What is Trade Assurance payment method:
A: It’s a free service which can protect your orders from payment
to delivery.
And we now have USD104,000.00 of caution money to assure your
orders.
7. Q: Do you have a warranty?
A: Yes, we have the warranty of 12 months.
