power supply for addressable rgb led strip

MODEL

BTB0000

OUTPUT

DC VOLTAGE

12V 5V 15V 24V 48V

RATED CURRENT

1A -50A

CURRENT RANGE

0 ~ 1.3A

RATED POWER

1-1000w

RIPPLE & NOISE (max.) Note.2

120mVp-p

VOLTAGE ADJ. RANGE

10.8~13.2V

VOLTAGE TOLERANCE Note.3

±1.0%

LINE REGULATION Note.4

±0.5%

LOAD REGULATION Note.5

±0.5%

SETUP, RISE TIME

1000ms, 30ms/230VAC 1000ms, 30ms/115VAC at full load

HOLD UP TIME (TYP.)

70ms/230VAC 12ms/115VAC at full load

INPUT

VOLTAGE RANGE

85~264VAC 120~370VDC

FREQUENCY RANGE

47~63HZ

EFFICIENCY (Typ.)

81%

AC CURRENT

0.35A/115VAC 0.25A/230VAC

INRUSH CURRENT (max.)

COLD START 65A/230VAC

LEAKAGE CURRENT

Less than 2mA/240VAC

PROTECTION

OVER LOAD

Above 105% rated output power

Protection type : Hiccup mode, recovers automatically after fault condition is removed

OVER VOLTAGE

13.8 ~ 16.2V

Protection type : Shut off o/p voltage, clamping by zener diode

OVER TEMPERATURE

U1 Tj 140°C typically (U1) detect on main control IC

Protection type : Shut down o/p voltage, recovers automatically after temperature goes down

ENVIRONMENT

WORKING TEMP.

-20~+70°C (Refer to “Derating Curve”)

WORKING HUMIDITY

20~90% RH non-condensing

STORAGE TEMP., HUMIDITY

-40~+85°C 10~95%RH

TEMP. COEFFICIENT

±0.03%(0~50°C)

VIBRATION

10 ~ 500Hz, 5G 10min./1cycle, period for 60min. each along X, Y, Z axes

SAFETY&EMC

SAFETY STANDARDS

UL60950-1, TUV EN60950-1 approved

WITHSTAND VOLTAGE

I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC

ISOLATION RESISTANCE

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25°C/ 70% RH

EMC EMISSION

Compliance to EN55022 (CISPR22) Class B, EN61000-3-2, -3

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-1, light industry level, criteria A

QTHERS

MTBF

1608.8Khrs min. MIL-HDBK-217F (25°C)

DIMENSION

62.5*51*28mm (L*W*H)

PACKING

0.13Kg; 108pcs/15Kg/0.71CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Line regulation is measured from low line to high line at rated load.

5. Load regulation is measured from 0% to 100% rated load.

6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”