CA40MM RCA40MM type submerged pulse jet valves for dust collector
machine G1 1/2
Description
Very high performance diaphragm valve designed to be mounted
directly into the compressed air manifold. 1" and 1.5" models are
supplied with outlet pipes to length specified, 3" model is
supplied without outlet pipes.
Suitable for
Dust collector applications, in particular for reverse pulse jet
filter cleaning including bag filters, cartridge filters, envelope
filters, ceramic filters, and sintered metal fibre filters.
Installation
1. MM valves are installed through the tank, refer to the
appropriate template listed
above.
2. To avoid any potential operational problems it is preferable
that the valves are
not mounted underneath the tank where condensation may collect. All
o-rings
should be coated with a silicone based lubricant or similar.
3. Dresser nut seals where used are a pressure seal only, not a
structural
component. Do not rely on dresser seals to retain either the tanks
or blowtubes.
Tanks and blowtubes must be independently restrained.
4. Tighten dresser nuts to 20Nm (15 ftlbs) max.
5. Tighten pipe outlets to 20 Nm (15 ftlbs).
6. Connect to FLY/AIRWOLF pilot valve, if remotely actuated.
7. Ensure compressed air supply is dry and free from oil and dirt.
8. Check all cleaning system components are secure before applying
pressure.
9. Apply moderate pressure and check for leaks.
10.Fully pressurise system.
11.Test fire and listen for proper actuation and crisp pulse
noises.
| Ordering Code | Port Size | Orifice | Flow Value |
| G Threaded | mm | Kv | Cv |
| CA25MM/RCA25MM | 1" | 25 | 26 | 30 |
| CA40MM/RCA40MM | 1 1/2" | 40 | 44 | 51 |
| CA50MM/RCA50MM | 2" | 50 | 76 | 88 |
| CA62MM/RCA62MM | 2 1/2" | 62 | 150 | 162 |
| CA76MM/RCA76MM | 3" | 76 | 200 | 233 |
| Construction |
| Body | Aluminum (Diecast) |
| Washer | SS 304 |
| Armature | SS 430FR |
| Core and Plugnut | Stainless steel |
| Core Spring | SS 304 |
| Sealing & disc | NBR(nitrile/buna-n) |
| Screws | SS302 |
| Diaphragm | PA-6(Standard), fluororubber |
| Shading coil | Copper |
| Connector | DIN43650A |
| Voltage | DC: 24V, AC: 24V, 48V, 110V, 230V |
| Working Temperature | -20 to +85℃ Nitrile seals -29 to +232℃ fluororubber seals |
| Protection Class | IP65 |
| Coil Insulation Class | F |
| Working Pressure | 0.35-0.85Mpa |
| Recommended on time range | 50-500ms |
| Recommended time between pulses | 1 minute or Less |
Dimensions
(Dimensions in mm and [inches])
After-sale Service
We can provide a series of after-sale service, such as product
introduction, mounting, debugging, technical support and so on.
Warranty
All item Comes with Basic 3 Month Sellers Warranty, if item
defective in 3 Month, We will offer replacement without extra
Charger(including shipping fee)After we Receive the Defective item.
If item Defective after 3 Month, Buyers can still send it back, We
will contact suppliers or Manufactory for Warranty. Buyers Might
Need to pay the Shipping fee For resend the replaced item.
