High Air Ventilating Plastic Material Dryers Stable Low Dew Point
Heatless Energy Saving
Descriptions :
EMDE series combines dehumidifying, drying and loading into one
unit. Heatless regenerator of dehumidifying and drying can provide
with dry air with lower dew point. Users can freely chosen needed
air flow rate, temperature, drying time and dew point value etc.
according to real production demand. The self optimization and
adjusting of regeneration temperature achieves energy-saving and
environment-protection, which saves above 60% energy compared with
traditional models.
Dew point values of drying can reach -70°C, drying barrel capacity
is 5-6000kg, can meet the production demand of different
environment and dosage.
ENM-Intelligent two-channel P.I.D. self-optimized temperature
controller and unique energy and airflow management software, can
real-time, intelligent, accurate control and self-optimized working
state of whole machine to reach energy saving and environment
protecting. Dew Point monitor is optional, convenient to monitor
dew point at any time.
Small size of whole, high effect working performance features good
dehumidifying effect and high air ventilating can provide stable
low dew point dry air for system, with energy saving and heat
preservation drying material barrel, the surface temperature of
drying material barrel is below 40°C when drying temperature
reached 180°C, hermetic system control to achieve efficient use of
energy and decrease unnecessary consumption of electric energy.
The hot air recycling system can avoid environment be polluted by
exhausted air, with shut-off suction box can make sure no
vestigital on pipe when conveying.
Hermetic circulatory system can prevent dried material from
moisture regaining because of outside contacting.
Drying air can evenly upward diffusion from barrel bottom to ensure
drying air can evenly dry material that after dehumidified, achieve
steady and rapid dehumidifying and drying if raw material.
| Main Technical Parameters |
| Model EMDE- | 12 | 25 | 50 | 75 | 100 | 150 | 200 |
| Drying Fan Power (kw) | 0.2 | 0.2 | 0.4 | 0.75 | 0.75 | 1.5 | 1.5 |
| Drying Heater Power (kw) | 2.2 | 3 | 4 | 4 | 6 | 7.2 | 12 |
| Full Insulation Barrel Capacity (L) | 20 | 40 | 80 | 120 | 160 | 230 | 300 |
| High-Pressure Air Capacity (m3/min) | 0.2 | 0.2 | 0.2 | 0.2 | 0.2 | 0.3 | 0.3 |
| High-Pressure Air Tension (bar) | 6-8 |
| Feeding Fan Power (kw) | 0.75 | 0.75 | 0.75 | 0.75 | 0.75 | 0.75 | 0.75 |
| ES-*Vacuum Hopper (L) | 3 | 3 | 7.5 | 7.5 | 7.5 | 7.5 | 7.5 |
| ES-*Electrical Hopper (L) | 3 | 3 | 7.5 | 7.5 | 7.5 | 7.5 | 7.5 |
| Suction Pipe (inch) | 1.5 |
| Voltage | 3Φ, 400V, 50HZ |
| Dimensions |
| H (mm) | 1070 | 1850 | 1850 | 2250 | 2180 | 2430 | 2430 |
| H1 (mm) | 970 | 1370 | 1370 | 1370 | 1600 | 1600 | 1850 |
| W (mm) | 715 | 1070 | 1070 | 1070 | 1190 | 1190 | 1350 |
| D (mm) | 550 | 620 | 620 | 620 | 820 | 820 | 900 |
| Weight (kg) | 120 | 300 | 300 | 300 | 410 | 410 | 530 |
