Fulund 3D pvc patch label making machine silicone drip mold machine
Dispensing Machinery price
Fulund has a long history since its establishment in 1999. Due to
the needs of development, the original brand (TYL) expanded the new
brand Fulund in 2022 . Fulund has customers all over the world,such
as international brands shoe manufacturer.
Fulund mainly products: Hot label machine, foam cutting machine,
insole hot stamping machine, shoe tongue transfer hot stamping
machine, insole heat transfer machine, insole cutting and transfer
integrated machine, insole printing machine, silk screen printing
machine, embossing machine, soft rubber equipment , vacuum
vulcanizing machine, silicone labeling machine, glue dispensing
machine, etc.
If the liquid has additives or needs to be combined with vacuum
defoaming, an electric stirrer should be installed in the barrel.
When the operability of the liquid is affected by the temperature
change, a temperature control system should be installed in the
barrel or pipeline.
If the liquid contains quartz powder or other abrasive powder
additives, it is recommended to use piston-type volumetric metering
products.
If there are additives in the liquid and there is serious
precipitation, the gear metering type cannot be used.
The mixing method of the two liquids depends on the proportion and
viscosity difference to decide whether to use static or dynamic
mixing.
When the viscosity difference between the two liquids A and B is
too large or the ratio is above 5:1, a dynamic mixer is required.
For use with automation equipment, please install a high and low
liquid level detector.
If the liquid crystallizes, in addition to the rubber storage tank,
temperature control must also be installed in the feeding pipeline.
When a large amount of glue is used in daily work, a feeding pump
can be used to replace the glue storage bucket.
If there are no air bubbles in the product during the potting
process, a vacuum infusion system is required.
PVC product process flow diagram:
1, Mixing: According to requirements, according to a certain proportion of
PVC materials, mixing evenly;
2, vacuum: The use of our special PVC vacuum equipment to remove bubbles;
3, dispensing: The PVC raw materials into the dispensing machine,
4, drying: After the injection molding table cut pieces into the
energy-saving oven or baking mold table, its drying and shaping;
5, filling the bottom material: after the molding table into the automatic bottom material filling
machine,
6, dry the bottom material: will fill the bottom material mold again into the energy-saving
oven or baking mold table dryingshape;
7, complete: Cooling table take out the product, Trim and tear off the leftover
material, the plastic part of PVC product isfinished.
Technical parameters:
| Model No. | FLD-P08D |
| Machine Size | 950*940*1500mm |
| Weight | 250KG |
| Electric heating power | 1.6KW |
| Effective Trip | 600*350*70mm |
| Worktable Size | 550*350mm |
Machine Features:
1: Shortcut keys can be set to facilitate the operation of workers,
avoiding the direct operation of the machine in the mode of fixed
order. With this function, the machine can be used flexibly. When
workers fully master the machine, it can also operate circularly,
which can greatly improve the efficiency.
2: Simple operation, multi needle and multi-color, flexible
configuration, simple operation, accurate dropping, and continuous
feeding without shutdown.
The needle can be extended to 8-18 colors, and multiple needles can
be combined at the same time without glue leakage. Full automatic
PVC drop plastic dispensing machine, with complete performance, is
a professional PVC drop plastic trademark machine.
This machine has the function of synchronous dispensing valve. For
example, 12 dispensing valves can be lowered simultaneously for
single color trademark, 6 dispensing valves can be lowered
simultaneously for double color trademark, 4 dispensing valves can
be lowered simultaneously for three color trademark, and so on.
This machine has more functions that other similar machines do not
have, that is, 12 different molds can be produced at the same time
within the usable range of this machine, which greatly improves the
use power of different molds and reduces the concern that some
customers think they can't use the glue dispenser if the quantity
is small.
3, High precision, high stability, fast and smooth rounding speed
and low sound. The accuracy can reach 0.01mm The product quality is
very stable, with uniform thickness and weight, and the product
qualification rate reaches more than 95%, reducing the waste of raw
materials. High stability: work for you continuously for 24 hours
to solve the worries of not delivering in time when receiving large
orders!
Application scope:
Drop plastic production of PVC trademark and soft rubber label
PVC cartoon and handicraft drop plastic production
Production of PVC shoes, bags and other clothing accessories
