Rustproof Heat Pipe Computer Cooling

Copper Fin Heat Pipe Radiator With Aluminum Extrusion Heat Sink And Fan

Quick Detail

Description

Heat pipe radiator is a new product produced by using heat pipe technology to make major improvements to many old radiators or heat exchange products and systems. There are two types of heat pipe radiators: natural cooling and forced air cooling. The thermal resistance of air-cooled heat pipe radiator can be made smaller, and it is often used in high-power power supplies.

Note

Side-blown radiator
Side-blowing radiators are extremely common on public graphics cards. We often see "brick" integrated radiators such as the public ATI Radeon HD 5870 and the public GeForce GTX 470 as the most typical side-blown radiators. The side-blowing radiator uses the side air flow generated by the rotation of the turbo fan to suck air from the inside of the chassis, and then pass through the air guide grooves, fins, heat pipes, etc., and discharge the heat to the outside of the chassis through the air outlet at the rear of the graphics card.
The disadvantages of side-blown radiators are mainly insufficient heat dissipation and unsatisfactory noise control.
Since the side-blowing radiator requires a long air guide channel and the fins are arranged inside the channel, a turbo fan is required to ensure a certain amount of air flow to allow air to flow out of the channel at a fast enough speed and take away heat. However, due to its size, the air volume of a turbofan is often unsatisfactory at low speeds. Once it is operated at a high speed, the noise of the cutting airflow of the turbofan blades will rise sharply. In actual use, some public graphics cards with turbo radiators have a core temperature of about 60°C in standby mode, while the core temperature quickly soars to 80-90°C under full load, and the noise will increase accordingly.
Although the side-blowing radiator has obvious disadvantages, in order to ensure that the temperature of the entire system in the chassis will not rise rapidly due to the heat of the graphics card, the mid-to-high-end graphics card in the public version uses an external side-blowing radiator. Only some graphics cards with lower heat output will choose other cooling modes.
Advantages: heat is discharged outside, does not aggravate the heat accumulation inside the case, and the temperature control effect inside the case is excellent (only refers to the outside heat dissipation). Disadvantages: The turbo radiator is noisy and the temperature control effect is not good enough.

The heat pipe radiator has the following advantages:

• The thermal response speed is fast, and its ability to transfer heat is more than 1000 times larger than that of copper pipes of the same size and weight;
• Small size and light weight;
• High heat dissipation efficiency, which can simplify the heat dissipation design of electronic equipment, such as changing air-cooling to self-cooling;
• No external power supply is required, and no special maintenance is required during work;
• It has good isothermal properties. After heat balance, the temperature gradient between the evaporation section and the cooling section is quite small, which can be approximately regarded as 0;
• The operation is safe and reliable, and does not pollute the environment.

We can offer the heat pipe radiator service, small qty is acceptable.

Technical Support

We can offer the design and simulation service. For example, our German customer's case.

According to the simulation results,the simulated chip is in compliance with the temperature requirements specficied by customer.

Dongguan Fodor Technology Co., LTD., founded in 2015, is committed to the development and sales of electronic heat sink and hardware electronic accessories, including: aluminum extrusion heat sink, cold forging heat sink, water cooling heat sink, cooling fan modules, aluminum stamping products and zinc aluminum die-casting products.Based on the development concept of "Rich quality & leading future", Fodor has the industry perfect supply chain resources, to provide customers with timely, efficient and high-quality services, reduce the inconvenience of customers in each procurement link, really make customers save time, effort and worry.

Fodor now has 2 senior engineers of water cooling radiator, 2 senior engineers of aluminum extrusion heat sink, 2 senior engineers of stamping, 2 senior engineers of fan module, and 10 other engineers and quality engineers, to control product design optimization and quality requirements.Sidework, Proe, CAD, PDF and other documents can be accepted by Fodor company for project consultation. The surface treatment that Fodor company can complete includes: anodizing, electrophoresis, complex acid salt, electroplating, painting, powder spraying, chromium plating and other processes to meet the needs of our customers.

Fodor adhering to customer first, achieve the win-win situation, is willing to establish the long-term cooperation relations with the general customers。