The OptiX Metro 100 supports various services interfaces, power
input modes, and installation modes, and a high security mechanism.
Various E1 Service Interfaces
The OptiX Metro 100 supports three types of physical interfaces:
RJ-45 (120 ohms)
BNC (75 ohms)
DB15 (X.21)
High Network Security Mechanism
The OptiX Metro 100 supports the Radius security control, that is,
the user names and passwords of all NEs are managed in a unified
manner through the server of the user. Any user must pass the
authentication before logging in to the NE. Therefore, the network
security is high.
Support for Device Stack
The OptiX Metro 100 supports a maximum of 1+3 device stack (one
master device and three slave devices), that is, 16xE1 services are
configured into one optical channel.
Support for Default Settings
The OptiX Metro 100 is configured and maintained with the NMS and
Web LCT, supporting the "one-click recovery to default settings"
function.
Various Installation Modes
The OptiX Metro 100 can be installed in various ways. Therefore,
you can select a proper installation mode according to the actual
situation.
The OptiX Metro 100 supports the following installation modes:
Cabinet-mounting (19-inch cabinet, ETSI 600 mm cabinet, or ETSI 300
mm open cabinet)
Wall-mounting
Desk-mounting
Various Power Input Modes
The OptiX Metro 100 supports the following power input modes:
110 V/220 V AC power input, the power input range is 90 V to 264 V,
with the frequency in the range of 47 Hz to 63 Hz.
-48 V/-60 V DC power input, the power input range is -38.4 V to -72
V.
The OptiX Metro 100 supports one AC power input and one DC power
input at the same time. The two power inputs back up for each
other. The AC power input is controlled by a switch, whereas the DC
power input is not. When the AC power input and the DC power input
are unavailable at the same time, the OptiX Metro 100 reports the
VOLT_LOS alarm indicating a power failure.
Low Power Consumption, Natural Heat Dissipation, and High
Integration
Supports a maximum power consumption of 16 W only.
Supports natural heat dissipation and produces low noise.
Supports high integration.
Service Types
The OptiX Metro 100 supports SDH services,PDH services,Ethernet
services.
Service Type
Maximum Access Capacity
SDH services
2xSTM-1 (o)
PDH services
4xE1
Ethernet services
2xFE (e)
Function Unit
Functions and features of the PDH unit
Functions and Features
Description
Basic function
Transmits and receives 4xE1 services.
Alarm and performance event
Supports various alarms and performance events, which facilitates
the management and maintenance of the equipment; supports the alarm
reversion function.
Clock source
Supports the settings and query of 4xE1 clock re-timing function.
Supports the extraction of E1 clocks over channel 1 only.
Maintenance features
Supports inloop and outloop at E1 ports so that faults can be
located quickly.
Supports the setting of overhead bytes to be sent/received, thus
enabling the board to function as an overhead instrument.
Supports the settings of thresholds for the excessive errors.
Supports pseudo-random binary sequence (PRBS).
Overhead processing
Processes path overheads at the VC-12 rate.
Supports the settings and query of overhead bytes such as J2 and
V5.
Other functions
Supports three types of E1 interfaces: RJ-45 (120 ohms), BNC (75
ohms), and DB15 (X.21).
Functions and features of the SDH unit
Functions and Features
Description
Basic function
Transmits and receives 2xSTM-1 optical signals.
Alarm and performance event
Supports various alarms and performance events, which facilitates
the management and maintenance of the equipment; supports the alarm
reversion function.
Clock source
Supports the line clock extraction function.
Maintenance features
Supports the outloop on SDH optical interfaces and inloop and
outloop on VC-4 paths, and the automatic release of loopbacks.
Supports the setting of overhead bytes to be sent/received, thus
enabling the board to function as an overhead instrument.
Supports the settings of thresholds for the excessive errors.
Supports PRBS.
Overhead processing
Provides transparent DCCs and orderwire byte channels.
Supports the setting and query of J0, J1, and C2 bytes.
Optical module
Supports the query of the manufacturing information about SFP
modules.
Supports the automatic laser shutdown (ALS) function of lasers.
Functions and features of the clock unit
Functions and Features
Description
Clock protocol
Supports the Standard Synchronization Status Message (SSM)
protocol.
Working mode
Supports the tracing mode, hold-over mode, and free-run mode.
Clock source
Supports the line clock extraction function.
When the tributary is normal, 2 MHz clock is extracted and
transmitted to the cross-connect and timing module; when the
tributary is abnormal, the cross-connect and timing module does not
use 2 MHz clock.
Only the extraction of E1 clocks over channel 1 is supported.
Functions and features of the power unit
Functions and Features
Description
Power supply types
Supports AC and DC power supplies.
Power supply protection
The AC power input and the DC power input back up for each other.
When the two power inputs are unavailable, the VOLT_LOS alarm is
reported.
Power detecting unit
Supports the detection on the AC power input and DC power input.
When either of the power inputs fails, the POWER_FAIL alarm is
reported.
Ethernet features supported by the OptiX Metro 100
Feature
Description
Ethernet frame encapsulation format
Supports the GFP-F, LAPS, and HDLC encapsulation formats.
Jumbo frame
Supports the setting of the frame length to a value ranging from
1518 bytes to 9600 bytes.
Supports a jumbo frame with a maximum length of 9600 bytes.
Mapping mode
Supports VC-12 or VC-3 virtual concatenation.
Ethernet test frame
Supports Ethernet test frames.
Interface Characteristics
Supports auto-negotiation, 10/100M full-duplex working modes.
Supports traffic control at port, counting of transmitted and
received packets, and query of port state.
Loopback
Supports Physical layer inloop or MAC layer inloops/outloops at the
Ethernet port.
Supports inloops and outloops on VC-3 channels, and the automatic
release of loopbacks.
LCAS
Supports link capacity adjustment scheme (LCAS).
LPT
Supports point-to-point link pass through (LPT).
RMON
Supports remote network monitoring (RMON).
Transfer or discard of frames shorter than 64 bytes
Supports the discard (default setting) or transfer of frames
shorter than 64 bytes. This function can be enabled or disabled on
the NMS.
Frames with frame check sequence (FCS) errors
Supports the transparent transmission of frames with FCS errors.
This function can be enabled or disabled on the NMS.
Minimum frame length
Supports the setting of the minimum frame length to 64 bytes.
Functions and features of the extended unit
Functions and Features
Description
Basic function
Supports the aggregation of a maximum of 16xE1 services into one
optical path.
Maintenance function
Supports loopbacks on stacking interfaces.
Specification
Specifications
Metro 100
Aggregation
STM-1
Dimensions
43.6 mm (H) x 442 mm (W) x 220 mm (D)
Switch Capacity
1.25Gbit/s full higher order and lower order cross-connect capacity
Supported Interfaces
STM-1(o), E1(e), FE(e)
Power Supply
DC: -48V DC or -60V DC AC: 220V/110V AC
Networking Mode
Supports multiple SDH networking topologies, such as chain, ring,
tangent rings, intersecting rings, etc
Clock Synchronization
Line clock source Tributary clock source One external clock input/output (2 Mbit/s)
Cargo will be delivered within 1 day after payment arrived.
Tracking Number will be offered once delivery done.
Delivery Options
Estimated Delivery Time
DHL
3-5 business days
Fedex
3-5 business days
By Sea
10-20 business days
Notice:
Above mentioned information are just for your reference only,we
will keep you posted for the tracking delivery schedule.There are
two delivery options available for by air and by sea:
Deliver to port:
Uonel is responsible for transporting goods to port. All subsequent
customs and transportation fees are the responsibility of the buyer. Uonel will recommend trustworthy local
freight forwarders to you.Uonel can facilitate the progress under
buyer's permission and at buyer's expense.
Deliver to door:
Uonel will quote all destination charge prior once we have
confirmed order. Uonel is responsible for transporting goods to door after you have
made the payment.
If your Huawei products failed, you must contact your sales
representative to verify product failure. If the problem still
can't correct by remote support methods i.e. email or phone
support, the RMA procedure will issue.
Company Profile
Uonel is one of the biggest Huawei Network Hardware distributor in
china, founded in 2008. We are a global provider of netwotking
products with more than 5000 customers.
We provide original new Huawei Routers,Switches,Firewalls,Wireless
APs & controllers,OLTs,GPON modems,optical transceivers.Our company
have more than $5million Huawei products in stock.
Most of our technical engineers had work exprience in Huawei
company,we can provide network
design&planning,configration,troubleshooting,maintenance and
training service in world wide.
Shenzhen Uonel Technology Co., Ltd. is a Global Provider of
Telecommunication Equipment and Services. We buy&sell Original NEW&REF telecom equipment from
carriers and market to other companies who need them. We offer carrier class telecommunication hardware at 80-90% OFF
list. We provide network design&planning, configration,
troubleshooting, maintenance and training service in world wide.
Uonel Products& Stock
More than $5million Huawei ZTE Juniper Cisco products in stock. Delivery your order within 72hours base on quick response ability. Focus on High-end telecom products including IP
Data,Transmission,Wireless,Server&Storage and spare parts.
Fedex
By Sea
Notice:
Deliver to port:
Deliver to door:
100% Low Price Guarantee:
100% Quality Assurance:
Free Technical Support:
100% Money Back Guarantee:
Flexible Secure Payment & Shipment:
