Totem pole output Z48 rotary encoder module external diameter 48mm
hole 8mm customizable
About Encoder Vibration
Vibration acting on an encoder always cause wrong pulse easily.
So we have to pay more attention to encoder working place.
The more pulse per round, the narrower groovy spacing of grating,
ore effect to encoder by vibration, when motor speed is low or even
stopped, vibration acting on encoder shaft or encoder shell would
cause grating vibration, in this way, encoder might show wrong
pulse signal.
Video of Encoder products
There are plenty of encoder video if you still have any doubts on
encoder, please email us directly or contact online service right
now.
At the same time, you could also visit our YOUTUBY page easily.
Most of the encoder series have videos for reference.
Z48 encoder Product introduction
| Items | Basic parameters |
| Brand | HENGXIANG |
| Encoder type | bearingless encoder |
| External diameter | 48mm |
| Thickness | 22.5mm |
| Dimension of limiting slot | 30mm, depth 2.4mm |
| Installation dimension | R22.35mm |
| Hollow shaft type | through hole |
| Output phase | Phase A+,B+,Z+,A-,B-,Z-,U+,V+,W+,U-,V-,W- |
| Supply voltage | DC5V ; DC8-30V |
| Outlet type | Cable out from side |
| Output mode | NPN/(Open Collector Output) |
| line drive (26LS31) TTL |
| line drive(DC8-30V) HTL |
| Cable length | 500mm |
| Consumption current | 100mA MAX |
| Top response frequency | 300KHZ |
| Allowable ripple | ≤3%rms |
| Load Voltage | ≤DC30V |
| Insulation strength | AC500V 60s |
| Insulation resistance | 10MΩ |
| GND | not connect to encoder |
| Mark to Space ratio | 45% to 55% |
| Environmental temperature | Operating:-20 ～+80°；storage:-25 ～+90° |
| Environmental humidity | Operating and storage: 35-85%RH(noncondensing) |
| Material | aluminum alloy |
| Certification | CE |
| package | Carton box |
| Net weight | About 60g (with package) |
Some encoder model number for reference
Z48-J3N1024
Z48-J4C1220
Z48-J6E2000
Z48-J12C2048/4
Z48-J1N2048
Z48-J2C2500
Z48-J3N50
Z48-J4C60
Z48-J6E500
Z48-J12C2500/8
Signal Circuit of encoder
1. The NPN Open Collector -- The NPN Open Collector(NPN) is an
interface based on an output circuit with an NPN transistor.
An open collector is the unconnected collector connection of an NPN
transistor, whose emitter is connected to earth and whose collector
is connected to the output.
2. PNP output
The PNP output is an interface based on an output circuit with a
PNP transistor.
3. Push-Pull output(HTL)
High Voltage Transistor Logic functions with a voltage supply in
the range 10 and 30 V DC, with 24 V DC being the most usual.
“Low” is defined as an output of between 0 V and 3 V and “high” as
between VCC and VCC - 3.5 V.
4. TTL RS-422 output
In a transistor-transistor logic (TTL), both the logical status and
the amplification are done by transistors, hence the name.
The TTL output is supplied with either a fixed 5 V voltage or a
variable voltage of between 10 and 32 V. For this the low range is
defined as the ≤ 0.4 V and the high range as ≥ 2.4 V.
