Drilling Rig Machine
Jinke JK830 Heavy Duty Crawler DTH Drill Rig 165mm Max Hole Diameter Diesel Quarry Blast Hole Drilling
Jinke JK830 Heavy Duty Crawler DTH Drill Rig For quarries that drill big patterns, the JK830 in heavy duty trim runs 165mm holes all shift without complaints. The frame, mast and feed system are built heavier than the standard machine, and the hydraulic system is tuned for long cycles on hard granite and basalt. Main Features 165mm max hole diameter for production blast patterns Reinforced mast and feed beams for heavy DTH hammers High torque rotation head handles stuck tools
JK850 Geothermal Drilling Rig 850m Depth 600mm Diameter Rotary Table Borehole Machine Heat Exchange
JK850 Geothermal Drilling Rig Geothermal boreholes put two demands on a rig: depth and torque. The JK850 covers both. It is rated to 850 meters, which is deep enough for closed-loop heat exchange fields and for many production-scale geothermal projects. And with 34KN.m of rotary table torque, it keeps turning in the hard, abrasive formations that geothermal work usually hits. Most of our geothermal customers run the electric motor version because drilling sites near buildings
Jinke JK830 Crawler DTH Drilling Rig 105-165mm Hole Diameter 125HP Diesel Quarry Mining Blast Hole
Jinke JK830 Crawler DTH Drilling Rig The JK830 is a crawler mounted DTH drilling rig made for quarry and mine blast hole work. It drills 105-165mm holes with a 125HP diesel engine driving the hydraulic system, and it moves itself around the bench on steel tracks, so one operator can handle positioning, drilling and rod handling without a support vehicle. Main Features DTH hammer drilling through hard rock without slowing down Crawler tracks with independent drive for rough
Jinke JK830 Multi Purpose Crawler Drilling Rig 105-165mm Blast Hole Machine for Foundation Anchor Work
Jinke JK830 Multi Purpose Crawler Drilling Rig Contractors who buy the JK830 usually start with one job in mind, then find it does three. The mast angles and the rotation speed range are wide enough for blast holes, foundation piers, rock anchors and slope stabilization holes, which is why we sell it as a multi purpose rig. Main Features Mast tilts from vertical to horizontal for anchor and tie-back holes Wide rotation speed range suits DTH bits and auger tools Crawler tracks
JK850 Diesel Engine Water Well Drilling Rig 850m Depth Rotary Table Borehole Drilling Equipment
JK850 Diesel Engine Water Well Drilling Rig A lot of the wells our customers drill are far from any power line. That is exactly why we offer the JK850 with the diesel engine. The rig becomes completely self-contained - you bring the machine, the drill pipe, and the fuel, and you can start drilling the day you arrive. The diesel engine drives the rotary table through the same four-speed gearbox as the electric version, so you keep all four speeds (40, 80, 160, 320 r/min) in
Jinke JK810 Crawler Rock Anchor Drilling Rig 90-140mm Hole Diameter Slope Stabilization Machine
JK810 Crawler Rock Anchor Drilling Rig The JK810 is the rig our customers use for rock anchoring and slope stabilization work. It drills 90 to 140 mm holes to install rock bolts, soil nails, anchor tendons and micropiles on highway cuts, retaining walls, and landslide-prone slopes. The crawler base lets it sit on the slope itself, which is exactly where a truck-mounted rig cannot go. One operator runs it. The engine, compressor and hydraulics are all on the machine, so there
Jinke JK810 Crawler Solar Pile Drilling Rig 90-140mm Hole Diameter Ground Mount Foundation Machine
JK810 Crawler Solar Pile Drilling Rig The JK810 is the machine our customers run on solar farm sites for drilling pile holes. It drills 90 to 140 mm holes to the depth needed for ground-mount solar panel support piles. Because the engine, compressor and hydraulics are all on one crawler base, it works on the uneven, hilly ground where truck-mounted rigs cannot get to. A solar farm means hundreds or thousands of holes in a row. The JK810 is set up for that. One operator drives
Jinke JK860 Crawler Mounted DTH Drilling Rig 115-178mm Hard Rock Water Well Borehole Machine Diesel 180HP
Jinke JK860 Crawler DTH Drilling Rig for Hard Rock Water Wells Hard rock water wells are a different job from drilling in soil: you need a DTH hammer, enough air, and a rig that can move between boreholes without a truck and crane crew. The JK860 crawler does exactly that. It drills 115-178mm holes and walks itself around the site on steel tracks. Main Specifications Drilling Method Down-The-Hole (DTH) Hole Diameter 115-178mm Engine 132kW / 180HP diesel Rotation Torque 3500
JK850 Large Diameter Water Well Drilling Rig 600mm Hole 850m Depth Rotary Table Municipal Wells Machine
JK850 Large Diameter Water Well Drilling Rig Municipal and industrial wells usually need more water than a small-diameter hole can deliver. The JK850 handles this properly: it drills holes up to 600mm in diameter and still reaches 850 meters deep. The 850mm through-hole rotary table is the key - it gives you room to run big casing and large-diameter tools without restriction. Big holes need big mud flow. The 850 L/min mud pump keeps the annulus clean and carries cuttings out
JK850 Electric Motor Water Well Drilling Rig 110KW 850m Depth 600mm Diameter Rotary Table Borehole Machine
JK850 Electric Drive Water Well Drilling Rig If your site has three-phase power available, the electric version of the JK850 is the cheaper machine to run over a full year. There is no diesel to haul in, no fuel tank to keep topped up, and the motor is noticeably quieter than a diesel at full load. The 110KW Y315S-4 electric motor drives the same rotary table, the same 80KN main hoist, and the same mud pump circuit as the diesel version - nothing gets downgraded because you
Jinke JK810 Crawler Water Well Drilling Rig 90-140mm Hole Diameter 60m Depth
JK810 Crawler Water Well Drilling Rig The JK810 is our crawler drilling rig that most customers buy for water wells. It drills 90 to 140 mm holes and goes down about 60 meters with a 3-inch or 4-inch DTH hammer. Farmers use it for irrigation wells, villages use it for drinking water boreholes, and contractors use it for dewatering and small geotech jobs. Everything is on one machine. The diesel engine, the screw compressor, the hydraulic pack and the mast all sit on a single
Jinke JK930 Multi Purpose Drilling Rig 300m Water Well Geothermal Mining 6X4 Mobile Hydraulic Rotation Head
Jinke JK930 Multi-Purpose Mobile Drilling Rig One Rig, Four Applications The JK930 multi-purpose rig is designed for drilling contractors who cannot afford to own separate equipment for different job types. Water well drilling today, blast hole drilling tomorrow, geothermal exploration next week — same machine, just change the tooling and drilling mode. On a single 6X4 mobile truck chassis, the JK930 packs a high-pressure air compressor, mud pump, foam injection system, and
JK1300 Hard Rock Water Well Drilling Rig 300m Depth DTH Hammer Tricone Bits Basalt Granite Drilling Machine
Standard water well rigs struggle in hard rock. Regular roller bits wear out fast on basalt or granite and you end up spending more time changing bits than drilling. This JK1300 comes set up for hard formations. What makes it different: DTH (Down The Hole) hammer system - hammer goes down behind the bit, hits close range. Way more effective than top hammer in deep holes High pressure air compressor included - 25 bar, enough to drive DTH hammer at 300m Tricone bit set - 6 bits
Jinke JK830 Crawler Water Well Drilling Rig 105-165mm Hole 125HP Diesel Engine 100m Depth
Jinke JK830 Crawler Water Well Drilling Rig Water well drilling is a different job from quarry work - you are chasing water, not breaking benches. The JK830 handles it with DTH or rotary drilling up to 100m depth, and because it is crawler mounted, it walks into village yards and rough sites where a truck rig cannot go. Main Features DTH and rotary drilling modes for different ground conditions 100m drilling depth with standard 3m drill pipes Crawler mounting - no truck or
JK850 Deep Water Well Drilling Rig 850m Depth 47m Mast 80KN Hoist Rotary Table Drilling Machine
JK850 Deep Water Well Drilling Rig When the water table sits 400, 600, or 800 meters down, a small rig simply cannot get there. The JK850 is built for exactly those jobs. It is rated to 850 meters and is regularly used for community water supply projects where shallow wells have run dry or turned saline. Depth capability is not just about the rotary table. It comes from the whole package working together: 34KN.m of torque to turn the bit in deep, compacted formations; an 850
Jinke JK930 Truck Mounted Water Well Drilling Rig 300m Depth 6X4 Chassis Air DTH Hammer Mud Rotary
Jinke JK930 Truck Mounted Water Well Drilling Rig - 300m Product Overview The JK930 is Jinke's proven 300-meter class truck mounted water well drilling rig, built on a 6X4 heavy truck chassis. It combines a high-pressure screw compressor for DTH air hammer drilling with a mud pump system for rotary drilling — giving operators the flexibility to switch methods based on formation conditions without changing equipment. The hydraulic system features independent oil cooling,
Skid-Mounted JK1300 Water Well Drilling Rig 300m Drilling Depth DTH Hammer Rock Drilling Machine
Some customers already have trucks or want to mount the rig on a used chassis to save money. This is the JK1300 rig unit on its own, mounted on a heavy steel skid base. What you get: Complete JK1300 drilling assembly - mast, rotary table, hydraulic system, control panel Steel skid base with mounting holes pre-drilled for HOWO, Shacman and ISUZU patterns BW850 mud pump with hoses 100m of 89mm drill pipes Standard bit set Engine and hydraulic power pack mounted on skid Mounting
JK860 Crawler Mounted DTH Drill Rig 115-178mm Borehole Diameter Blast Hole Machine for Quarry Mining
The JK860 is a crawler-mounted DTH drill rig built for blast hole drilling in quarry and open-pit mining. It handles borehole diameters from 115mm to 178mm with a maximum drilling depth of 30 meters. The rig runs on a 132kW diesel engine with a fully hydraulic control system and comes with an integrated wet dust collector. Compact enough to maneuver on uneven quarry benches yet powerful enough for continuous production drilling.
Jinke JK930 Multi Purpose Drilling Rig 300m Water Well Geothermal Mining 6X4 Mobile Hydraulic Rotation Head
Jinke JK930 Multi-Purpose Mobile Drilling Rig One Rig, Four Applications The JK930 multi-purpose rig is designed for drilling contractors who cannot afford to own separate equipment for different job types. Water well drilling today, blast hole drilling tomorrow, geothermal exploration next week — same machine, just change the tooling and drilling mode. On a single 6X4 mobile truck chassis, the JK930 packs a high-pressure air compressor, mud pump, foam injection system, and
JK860 Hydraulic Rotary Water Well Drilling Rig 860mm Rotary Table for Deep Borehole Engineering
The JK860 hydraulic rotary drilling rig is rated for 1000m boreholes with an 860mm through-hole rotary table delivering 50KN.m torque. Available with 132KW electric motor or diesel engine, 55m mast with 100KN main hoist. Skid-mounted base with optional crawler tracks for site mobility.