Wireline Pressure Control Equipment
Wireline Lightweight Lubricator 3Inch 10,000PSI Wireline Pressure Control Equipment
Wireline Lightweight Lubricator 3Inch 10,000PSI Wireline Pressure Control Equipment overview The lightweight lubricator is pipe with standing high pressure, used to accommodate the entry and exit of downhole tools into the well under pressure. The lightweight lubricator can accommodate basic tool strings such as rope caps, weighting rods, and impact arrestors. The lower part of the lightweight lubricator tube pipe is connected to the blowout valve, and the upper part is
Wireline Slickline Pressure Test Plug And Test Cap And Lifting Cap Control Equipment
Wireline Slickline Pressure Test Plug And Test Cap And Lifting Cap Control Equipment Introduction The internal and external pressure test plug is a kind of auxiliary tool that uses thread and sealing surface to connect and seal the tools and equipment that need to be tested for pressure, and to test the tools for pressure.The BOP holder is the base for a ground-mounted BOP. It can be installed in any position and is connected with a standard NPT connector to allow pressure
Cable Cutter Suited Wireline Pump In Tee Pressure Control Equipment
Cable Cutter Suited Wireline Pump In Tee Pressure Control Equipment Overview: The cable cutter is located above the grease tube upper check valve, next to the lower end of the grease tube inlet. Its role is mainly that the cable is stuck in the work to help it not be able to carry out any movement, at this time, the shear can be used to cut the cable cleanly, so as to recover. Structural features The cable cutter is composed of a shell, a body, a shear piston, a plug cap, a
Flange Half Moom Flange Wellhead Adapter Wireline Pressure Control Equipment
Flange Half Moom Flange Wellhead Adapter Wireline Pressure Control Equipment Overview The wellhead flange is used to connect the wellhead, the upper part is connected to the tubing , and the lower part is connected to the wellhead. The wellhead flange is connected by bolts and nuts. When in use, the gasket is placed between the sealing surface, after tightening the nut, the specific pressure on the surface of the gasket will be deformed after reaching a certain value, and the
Oilfield 70MPA Wireline Pressure Control Equipment FD7.6-70-Y for 5-3/4-4ACME.O Type Connection Hydraulic Tool Trap
Hydraulic Tool Trap Wireline 5-3/4-4ACME.O Type 70MPA Wireline Pressure Control Equipment Product overview Hydraulic Tool Trap also known as trap. It is a safety device to prevent the tool string from falling into the well accidentally when the tool string is pulled out. It is installed below the blowout preventer and above the BOP. Technical specification PRODUCT MODEL FD7.6-70-Y CONNECTION 5-3/4″-4ACME.O Type I D 76MM (3inch ) WORK PRESSURE 70Mpa(10000PSI) TEST PRESSURE
BOP Hydraulic Control System H2S 70Mpa 10K Wireline Pressure Control Equipment
BOP Hydraulic Control System H2S 70Mpa 10K Wireline Pressure Control Equipment Overview A Blow out Preventer (BOP), which is connected to a wellhead adapter or the top of an oil tree. Closing the BOP while the wire or cable is still downhole seals around the wire (or cable), sealing the pressure inside the well and preventing external blowout. Structural features The blowout preventer is composed of shell, ram assembly, equalizing valve assembly, manual control mechanism,
70Mpa 10K Hydraulic Tool Catcher For Wireline Pressure Control In EE Environments
Hydraulic Tool Catcher 70Mpa 10K H2S Wireline Pressure Control Equipment Overview The hydraulic tool catcher is composed of a body, a mandrel, a fish claw, a lower joint, a nonnut, a guard plate, a piston, a spring, etc., a seal and a rubber part. The lower end lower joint is connected to the wellhead joint. The upper end is nonexistent and can be connected to the wellhead device. Under the control of spring and external hand pump, the fishing claw inside the hydraulic trap
10T Safe Load Wireline Pressure Control Equipment 720MM OD Hay Pulley Cable for Operation and Slickline
Hay Pulley Cable ￠720MM OD Wireline Pressure Control Equipment Product overview The cable hay pulley is mainly used to guide the cable (or wire) to lower or raise the instrument into the well. The top of the bracket is provided with a lifting ring, which can be used for lifting operations with shorter lifting ropes to reduce the difficulty of work. Moreover, the direction can be adjusted arbitrarily to facilitate the free rotation of the cable hay pulley on the stuffing box.
105MPa Chemical Injection Valve Injection Sub Wireline Pressure Control Equipment
105MPa Chemical Injection Valve Injection Sub Wireline Pressure Control Equipment I. Overview: The chemical injection sub is designed to apply a deicer or corrosion inhibitor to the wire (cable) during a workover operation. The chemical injection sub is installed under the grease head or stuffing box and uses a replaceable felt filler to wrap the wire and prevent chemicals from passing through the hole. II.Structural features and application: The chemical injection head is
Wireline Lubricator Wireline Riser And Slickline Pressure Control Equipment
Wireline Lubricator Wireline Riser and Slickline Pressure Control Equipment I.Overview: A blowout Lubricator is a high pressure riser with a quick coupling that is used to carry downhole tools in and out of a well under pressure. The lower part of the blowout Lubricator is connected with the blowout Lubricator valve, and the upper part is connected with the blowout Lubricator box or grease injection sealing system. In the case of blowout Lubricator operation, the multi
Grease Injection Head With Stuffing Box 0.125inch-105MPa Wireline Equipment
Grease Injection Head With Stuffing Box 0.125inch-105MPa Wireline Equipment I.Overview Grease Injection Head With Stuffing Box is a surface pressure control device used to lubricate cables (or wire) and seal wellheads by injecting sealing grease into flow tube. The high pressure seal grease output from the grease pump enters the lower part of the flow tube and flows upward. In this process, the seal grease mixes part of the downhole oil and gas and finally drains out from the
Double Ram BOP 5K Pressure Control Wireline Preventer Manual Type
Double Ram BOP 5K Wireline Pressure Control Preventer I. Introduction The Double Wing Blowout Preventer is connected to the wellhead coupling or the top of the tree. Closing the BOP while the wire or cable is still downhole seals around the wire (or cable), sealing the pressure inside the well and preventing external blowout. II.peculiarity The Double Wing Blowout Preventer is a type of wireline pressure control preventer used in deepwater wells to prevent accidental kickout
Triple Hydraulic Valve BOP Wireline Pressure Control Equipment
Triple Hydraulic BOP Triple Hydraulic Wireline Valve Wireline Pressure Control Triple hydraulic BOP (Blowout Preventer) is a safety device used in oil and gas wells to prevent the release of gas or liquid from the wellbore. It consists of three hydraulic components: the blowout preventer, the wireline, and the wireline pressure control.The main function of the Triple Hydraulic BOP is to seal the wellbore and prevent any leakage of gas or liquid. The blowout preventer is
Alloy Steel Wireline Tool Trap Wireline Pressure Control Equipment 2 inch - 4 inch
Wireline Tool Trap Manual Wireline Pressure Control I.Product Description: Wireline Manual Tool Trap is a safety device designed to stop wireline tools from falling into the wellbore should the wireline accidentally break at the Rope Socket while in lubricator. This tool features hydraulic operated flappers to provide a passage for tools to enter the well bore when in open position. The hydraulic mechanism can be easily operated by using hand pump or remotely and therefore
Wireline Pulley Wellhead Wireline Pressure Control Equipment With 10 Inch Sheave
Wireline Pressure Control Wireline Pulley I. Introduction: The Wireline Pulley is used to pull the steel wire or cable from the top of the nozzles to the plane of the steel wire or cable drum, so that the tension point of the steel wire or cable is moved from the vertex to the oil tree, thereby reducing the tension load on the side of the steel wire or cable and preventing the damage of the nozzles from being pulled and bent. The ground pulley can also be lifted to change the
2" - 7" Pump In Tee Wireline Pressure Control Equipment API Standard
Pump-In-Tee Wireline Pressure Control EquipmentⅠ.IntroductionThe Pump in tee is attached below the BOP,The pump in tee connection thread is used to connect the wellhead manifold to provide a path for large flow. NPT thread hole on the other side of the tee body is a pressure release valve . After installing the pressure release valve, it can be used for pressure relief to ensure safe operation.II. General Technical Parameters BoreWork PressureServiceConnectionPN2.5＂5K 10KStd
10K Wireline Tee Joint Wireline Pressure Control Equipment 2" - 7"
10K Wireline Tee joint Wireline Pressure Control Equipment Ⅰ. Introduction The Wireline Tee joint is attached below the BOP,The Wireline Pumping tee connection thread is used to connect the wellhead manifold to provide a path for large flow. NPT thread hole on the other side of the tee body is a pressure release valve . After installing the pressure release valve, it can be used for pressure relief to ensure safe operation. II. General Technical Parameters Bore Work Pressure
20 Inch Cable Sky Pulley Wellhead Wireline Pressure Control Equipment
20 inch Cable Sky Pulley Wellhead Wireline Pressure Control I. Overview: The Cable sky pulley is used to pull the cable from the top of the nozzle to the lower part of the nozzle, changing the direction of the cable pull to facilitate wire operation by the winch. It is different from the cable ground pulley in that its anti-hopping board length is large . II.Specification of wireline hay pulley Number size Wire range Safety load 1 10inch 0.092”-0.125” 2.5t 2 12inch 0.092”-0
Alloy Steel Wellhead Joint Wireline Pressure Control Equipment 4inch ID
Wireline Wellhead Joint Wireline Pressure Control Equipment I. Overview: The wellhead joint is used to connect the blowout preventer with the wellhead, with the upper part connected with the blowout preventer and the lower part connected with the wellhead. The wellhead joint is sealed by threads. When in use, the wellhead connector can be directly tightened on the thread of the wellhead after winding the thread with tetrafluoroethylene tape or applying anti-sticking grease on
Nickel Alloy Material Wellhead Adapter Wireline Pressure Control Equipment
Wellhead Adapter Wireline Pressure Control Equipment Nickel Alloy Material I. Overview The Wellhead Adapter is used to connect the blowout preventer and the wellhead, the upper part is connected with the blowout preventer, and the lower part is connected with the wellhead. Wellhead Adapter are sealed by threads. When in use, wrap the thread with PTFE tape or apply anti-sticking grease on the thread, and then directly tighten the Wellhead Adapter on the thread of the wellhead.