Cable Testing Machine
Carbon Fiber Composite Core Winding Test Device For Specimen Of Diameter φ 5 - 11mm
Product description: Carbon fiber composite core winding test device is suitable for the winding property test of fiber reinforced polymer matrix composite core for overhead electrical conductors cables, fiber reinforced resin matrix composite core soft type aluminum wires. It is composed by a chassis, the mechanical transmission part,the control part, the winding wheel, a protective cover, assembly of the damping device, the guide tubes and other components. Standard: • GB/T
50N Or 100N Stripping Force Tester For Cable And Wires Testing
Product description: Stripping force tester is widely used for the stripping force, pressure resistance and bending test of wires, cables, terminals etc. Standards: • GBT 25085-2010 Technical parameters: • Max test force: 50N, 100N (optional for users) • Stroke: about 300mm • Speed: 50 ~ 250mm/min, settable • Relative error of test force indicating value: ≤±1% • Power system: AC rate regulating motor • Safety device: yoke plate lower limit protection device • Display: dark
IEC 60851-3 Winding Wires Winding Test Apparatus For Enameled Round Wire
Performance Characteristics 1.Executive standard: GB/T4074.3-2008,IEC60851-3 2.The winding test apparatus is suitable for measuring the flexibility, adhesiveness, thermal shock and other performances of the film of enameled round wire with nominal conductor diameter below 1.600mm; 3.Used with JRB-16 enameled round wire winding test bar; 4.This winding test apparatus can set any number of winding turns; 5.LED would automatically display and record the number of winding turns.
IEC 60794 High Precision Optical Cable Impact Testing Machine
General Introduction 1.1 Equipment overview Optical cable impact tester is used to detect optical fiber cables to withstand impact capability. By applying the impact force, the requirements for qualified optical cables is that fibers are not broken, and fiber attenuation changes do not exceed the specified value of optical cable product detailed specifications, the cable sheath jackets do not crack, which meets the test requirements to optical cable of method E4. Completely
EN50305-2018 Standard Railway Cable Tester with 400mm Effective Stroke and 0.45mm Steel Pin Diameter for Dynamic Cut-through Testing
General Introduction 1.1 Equipment overview Railway Rolling Stock Cables Dynamic Cut-through Tester is used to test the insulation strength of railway locomotive and vehicle cables. Squeeze the surface of the finished cable with a steel needle with a diameter of 0.45mm, increasing the pressure at a constant rate until the insulation or sheath is cut through. The instrument automatically stops when the steel needle contacts the internal conductor or metal shield and records
ISO6892 ISO7500 LCD Digital Display Universal Tensile Testing Machine with Large Deformation Extensometer and 800mm Effective Stroke
General Introduction 1.1 Equipment overview LCD digital display tensile tester (large deformation) is widely used for hardware, metal, rubber and plastics, footwear, leather, clothing, textiles, insulators, wires, cables, terminals and other types of materials, to test tensile, tear, peel, compression, bending and other materials research and development, inspection and test, with multiple functions, wide range of uses. LCD digital display tensile tester (large deformation)
ISO 9513 Computer Control Electronic Tensile Testing Machine with Large Deformation Extensometer for Plastic Rubber Cable
General Introduction Computer-controlled electronic tensile tester (large deformation) is widely used for hardware, metal, rubber and plastics, footwear, leather, clothing, textiles, insulators, wires, cables, terminals and other types of materials, to test tensile, tear, peel, compression, bending and other materials research and development, inspection and test, with multiple functions, wide range of uses. The computer-controlled electronic tensile tester (large deformation
IEC 60332-1 ISO 19642.2 Automatic Single Wire Flame Test Apparatus for Cable Testing Machine
General Introduction 1.1 Equipment overview Single wire and cable tilting flame tester is generally applicable to road vehicles 60V and 600V single core wire tilt anti-retardant standard,horizontal flame-resistant time standard and international automotive cable standards of low-voltage cables for automobiles unshielded horizontal flame test methods. lt is used for performance assessment of cable under fire conditions. Test method: Fix the two terminals of the sample, and put
UL 94 IEC 60695-11-10 Automatic Horizontal and Vertical Flammability Tester for Plastic Materials
General Introduction 1.1 Product Description Horizontal and vertical burning tester is mainly used to determine the non-combustible properties of plastics or films under the direct combustion of the specified ignition source, to judge the refractory grade of refractory materials. UL 94 is one of the most important UL standards for fire safety test methods. He is particularly important for plastics used in the electrical industry, and the test method is based on UL's research
IEC 60811-4-1:2004 and ISO 6964 Compliant Automatic Carbon Black Content Tester for Polyethylene Combustion Testing
General Introduction 1.1 Equipment overview Carbon black content test device is designed and produced in line with GB/T2951.41—2008 , used for determination of carbon black content of polyethylene, polypropylene, polybutylene plastics. 1.2 Related standards ISO 6964; IEC 60811-4-1:2004 ASTM D1603 Technical parameters Quartz tube: inner diameter 30mm, total length 600mm; Heating furnace: room temperature~600℃, 500mm length; Temperature sensor: K type, room temperature~1300℃;
UL1581 High Precision VW-1 (Vertical Specimen) Burning Test Machine for Wire and Cable
General Introduction 1.1 Product Description VW-1 (Vertical-specimen) Flame Tester is designed in accordance with UL1581 and approved by Guangzhou Meihua UL corporation,completely in line with W.1 fame test standard, is used for test of W.1 and FT.2. it's economic and applicable, which is widely used inwire and cable industry. The test is taken in a sealing laboratory which volume is 4.32 cubic meters. Test methods: Adjust the height ofthe flame, put the top of the fame under
IEC60331/EN50200 Fire Resistance,Mechanical Shock and Water Spray Testing Instrument for Cabled and Wires
General Introduction 1.1 Product Description Full standard fire test machine comprehensive GB, lEC and BS standards. The structure and performance of the combustion testmachine contains fire characteristics test, water and fire resistance test and mechanical vibration and fire resistance test. This instrument adopts computer software to control and monitor the test process of the current, voltage, gas flow, the test results ofthe curve can be output to print. lt is suitable
BS 6387 IEC 60331Cable Circuit Integrity Fire Resistance Tester Under Fire Conditions (Full Standard)
General Introduction 1.1 Product Description Full standard fire test machine comprehensive GB, lEC and BS standards. The structure and performance of the combustion testmachine contains fire characteristics test, water and fire resistance test and mechanical vibration and fire resistance test. This instrument adopts computer software to control and monitor the test process of the current, voltage, gas flow, the test results ofthe curve can be output to print. lt is suitable
IEC60332-1~2 Single Insulated Wire and Cable Vertical Combustion Tester (Rotor Flow Meter)
General Introduction 1.1 Equipment overview Single wire and cable vertical flame propagation tester is in accordance with IEC 60332-1-2:2004 . Obtain and determine wire and cable's capability of prevent the firefrom spreading under fire condition. Used for gaining and determining cable's capability of prevent the fire from spreading. Get one piece of 600mm cable as a testing sample, fix it on the clamp after processing. Select fire time based on testing sample specifications,
IEC 60754-1&2 Halogen, PH & Conductivity Testing Device on Gases Evolved During Combustion of Materials From Cables
General Introduction Halogen, PH & conductivity tester is used to measure gas volume of Halogen Acid (IEC 60754-1), pH concentration (PH Meter, Hydrogen ions, IEC 60754-2), Conductivity (IEC 60754-2) and etc from a wire (cable) by radiant heat in the Tube Furnace (IEC 60754-1: 800℃, IEC 60754-2: 950℃). Standards: IEC 60754-1~2-1994 Technical parameters Activated carbon (air filtering): filter for filtering the supplied air Silica gel (air drying): a device for drying the
IEC 61034 3M Cube (Wire and Cable)Smoke Density Apparatus Chamber for Fire Tester Instrument
General Introduction The 3M cube wire and cable smoke density tester is mainly used incable or optical cable combustion smoke density measurement system, which is in accordance with the latest GB/T17651 and lEC61034-2013 standards. Test Index: Optical density (OD) and specific optical density (DS) of the smoke Measuring Principle: Lambert - Beer Law Measuring Method: The smoke density is expressed by the fraction of the light transmittance of smoke in the initial light
IEC 60332-3-10 Bunched Cable Vertical Flame Spread Tester (mass flow meter)
General Introduction The Bunched Cable Vertical Flame Spread Tester is used to detect vertically mounted under specified conditions for vertical flame spread inhibiting the ability of bundle cable or fiber optic cable. In accordance with IEC60332—3—10: 2009
ISO 7500-1 and ISO 6892-1 Automatic Tensile Strength Tester (Large Deformation)
Product description: LCD digital display tensile strength tester (large deformation) is widely used for hardware, metal, rubber and plastics, footwear, leather, clothing, textiles, insulators, wires, cables, terminals and other types of materials, to test tensile, tear, peel, compression, bending and other materials research and development, inspection and test, with multiple functions, wide range of uses. LCD digital display tensile tester (large deformation) is adopted
Manual Dumbbell Shape Die Sample Cutter with Two Standard Dies
Product description: Dumbbell die sample cutter is used to cut rubber, insulation and sheath materials, make them to be standard-shaped sample for test. Allocated with various dumbbell cutter dies for different test requirement.requirements Standard: ·GB/T2951.11-2008 Technical parameters 1.Max stroke:35mm 2.Stroke adjustment range:100mm 3.Working bed size:210×170mm 4.International dumbbell cutter die:50x8.5x4mm,75x12.5x4mm 5.Dumbbell cutter die is able to be customized
IEC 60811-1-1 Double-head Skiving Machine for Grinding Rubbers Test Pieces
Product description: The double head skiving machine is specially designed for rubber factories and research institutions to grind rubber test pieces to a certain thickness for other testing equipment to conduct tests. It is one of the essential equipment in the inspection of rubber quality. The Skiving machine is mainly composed of main components such as the base feed carriage, working wheel, motor, grinding wheel, etc. The Skiving machine has a grinding wheel and a drag