SP-01 General Epoxy Floor Coating System

SP-01 General Epoxy Floor Coating System

Inquire Now

description :

SP-01 General Epoxy Floor Coating System
Product DescriptionSP-01 is a two component, abrasion resistant epoxy floor coating with the following properties:
lEasy-to-maintain, seamless surface
lExcellent adhesion and Chemicals resistance
lSlip resistance and customizable colors 
Application Area
Industrial &manufacturing
beverage processing
chemical processing
electronics
food processing
pharmaceutical production
mechanical rooms
warehouse/distribution
Transportation
automotive dealerships
parking decks
transportation terminals
vehicle maintenance areas
Common areas
aisleways/corridors
laboratories
loading dockTechnical Data (25C)
ITEMINDEX
Drying time, hTouch dry�� 4h,
Hard dry�� 24h.
Solid by weight 60
Adhesion  (grade)�� 1.
Pencil hardness��2 H
Impact strength, (Kg��cm-2)50 passed.
Abrasion resistance (750g/500r,weight loss, g)�� 0.04.
Water resistanceNo change in 48 hours.
Anti-10% sulfuric acidNo change in 56 days.
Anti-10% sodium hydroxideNo change in 56 days.
Anti-petrol, 120#No change in 56 days.
Anti-lubricantNo change in 56 days.Note:All the technical data stated in the above sheet are based on the tests; practical data may vary due to circumstances beyond our control.
 
Direction of Use
Surface preparation The compressive strength of the concrete substrate should not be less than 25N/mm2, the best application temperature is between 10~25.The air humidity must not be higher than 80%, the moisture content of the substrate shall not be higher than 8.Correct substrate preparation is critical for optimum performance. Surfaces should be sound, clean, dry and free from loose particles, oil, grease, and other contaminants.Clean oil, grease by special detergent. Cement laitance, loose particles, pitch and other contaminants must be removed from the surface by sand-blasting. The alkalinity and porosity of the surface must also be considered.
Primer SP-01A as a primer is adapted to seal the substrate. According to the oil absorption of substrate, a second sealer coat may also be required.
Putty Scraping the putty, SP-01A: SP-01B: quartz powder=1: 1: 2~3.
Base Coat Brush the base coat (SP-01A: SP-01B=1: 1) one or two layers. Finish coat Brush SP-01A as a varnish.
Pot life 0.5h at +25C
Cleaner Clean tools and equipments using a special detergent SP-01S before the coating curing.
Packaging
SP-01 A: 15kg per drum
SP-01 B: 15kg per drum
SP-01 S: 15kg per drum
Shelf life
12 months stored in original container, at a dry enclosed place at temperatures between 15 to 35 without exposure to direct sunlight.Health and safety information
Protective measures   SP-01 contains certain chemicals which can cause skin irritation. Wear gloves, masks while handling the product, washing thoroughly after handling. Should skin contact occur, wash immediately with soap and water.
During applying and curing in closed rooms, adequate fresh air ventilation must be provided. Keep away from open flames including welding.
In case of accidental eye contact, wash with a large quantity of water and immediately seek medical advice.
For detailed health, safety, environment recommendations, please consult and follow the instruction on the product material safety data sheet 
Disclaimer
The information given in this sheet is not intended to be exhaustive. Any person using the product without first making further written enquiries as to the suitability for the intended purpose does so at his own risk and we can accept no liability of the product for any loss or damage arising out of such use. The information contained product development. Product data are subject to change without notice and become void five years from the date of issue. SP-01 is for professional use only.
ISSUED in May 2006